View Issue Details

IDProjectCategoryView StatusLast Update
00033783 - Current Dev ListBugpublic2019-08-30 13:48
ReporterK7ZCZAssigned ToK7ZCZ 
PrioritynormalSeverityminorReproducibilityalways
Status resolvedResolutionfixed 
Product Version6.6.0.236 
Target VersionFixed in Version6.7.0.226 
Summary0003378: Rig control: several radios don't correctly handle input and output processor slider settings
DescriptionThe code in Rig Control to handle the Yaesu/Kenwood "PL" command isn't working correctly. Several variants of this command set the input and output processor strength settings in the same command. For example, "PL033055" would set the input level to 33 and the output level to 55.

Since the Rig Control UI wants to offer one control for each side, it will need to read the existing values from both sides, change the value for the side of interest, and then write the commanmd out.

The code to perform this function for almost all radios is badly broken and doesn't work. For most radios that have a single setting (PLnnn, which sets only the output processor), the code works fine.

Steps To Reproduce
1) Start up Rig Control, connected to one of the listed radios
2) Set the radio to view the input and output preprocessor levels. On the TS-890 ...
3) Make sure you're in a phone mode, like USB
4) Press and hold the bottom soft menu button labelled "PROC OFF" or "PROC ON" to reveal the speach processor settings
5) Assure that the "Speech proc. in" and "Speech proc. out" sliders are visible
6) Exercise the sliders.

BUG#1) The radio doesn't show the input or output level changing, an the slider snap back to the previous setting.

7) Use the + (F5) or - (F4) buttons on the radio's front panel to adjust either setting.

BUG#2) The radio changes it setting, but the change is not reflected in Rig Control's sliders

Additional InformationAs far as I can tell, the involved radios are these:

Yaesu FT-950
Yaesu FT-3000
Yaesu FTDX-991
Yaesu FT-891
Yaesu FTDX-1200
Yaesu FT-1200
Yaesu FTDX-9000
Yaesu FTDX-5000
Kenwood TS-480
Kenwood TS-590
Kenwood TS-2000
Kenwood TS-890
Kenwood TS-990
Kenwood TS-870
TagsFT-950, FT-991A, FTDX-1200, FTDX-3000, FTDX-5000, Kenwood, TS-2000, TS-480, TS-590, TS-890S, Yaesu
ModuleRig Control
Sub-ModuleRadio Support
TestingNot Started

Activities

K7ZCZ

2019-07-05 15:43

administrator   ~0008196

fixed in the 6.7 branch with this checkin:
https://hrdsoftware.visualstudio.com/HRD/_versionControl/changeset/5050

Issue History

Date Modified Username Field Change
2019-07-05 15:17 K7ZCZ New Issue
2019-07-05 15:17 K7ZCZ Tag Attached: FTDX-1200
2019-07-05 15:17 K7ZCZ Tag Attached: FTDX-5000
2019-07-05 15:17 K7ZCZ Tag Attached: Kenwood
2019-07-05 15:17 K7ZCZ Tag Attached: TS-2000
2019-07-05 15:17 K7ZCZ Tag Attached: TS-480
2019-07-05 15:17 K7ZCZ Tag Attached: TS-590
2019-07-05 15:17 K7ZCZ Tag Attached: Yaesu
2019-07-05 15:43 K7ZCZ Assigned To => K7ZCZ
2019-07-05 15:43 K7ZCZ Status new => resolved
2019-07-05 15:43 K7ZCZ Resolution open => fixed
2019-07-05 15:43 K7ZCZ Note Added: 0008196
2019-07-05 15:51 K7ZCZ Tag Attached: FT-950
2019-07-05 15:51 K7ZCZ Tag Attached: FTDX-3000
2019-07-05 15:51 K7ZCZ Tag Attached: FT-991A
2019-07-05 15:51 K7ZCZ Tag Attached: TS-890S
2019-08-30 13:48 K7ZCZ Fixed in Version => 6.7.0.226